友情链接: 澳门银河老虎机 澳门巴黎人手机网址 永利老虎机 澳门葡京官方赌场 葡京手机平台 葡京官方下载 澳门永利导航 永利百家乐 澳门金沙导航 澳门银河客户端 澳门葡京导航 永利手机平台 澳门永利官方下载 葡京客户端 葡京官方网址 澳门葡京官方注册 澳门永利老虎机 银河老虎机 永利手机网站 永利客户端 银河手机网址 金沙百家乐 澳门葡京现金网 金沙客户端 澳门葡京手机网站 金沙官方注册 澳门巴黎人导航 澳门银河轮盘 巴黎人官方赌场 永利官方注册 澳门葡京百家乐 澳门葡京官方下载 澳门金沙官方下载 葡京手机网站 澳门葡京手机平台 巴黎人老虎机 澳门金沙百家乐 澳门永利手机平台 澳门金沙客户端 澳门永利官方网址 银河官方网站 澳门葡京老虎机 巴黎人官方网站 葡京手机网址 葡京官方网站 葡京老虎机 澳门金沙官方注册 银河官方注册 澳门巴黎人百家乐 永利官方网址 金沙现金网 澳门永利官方网站 澳门葡京官方网站 澳门金沙轮盘 澳门永利官方注册 葡京轮盘 澳门巴黎人手机平台 澳门葡京官方网址 澳门永利百家乐 巴黎人轮盘 银河官方网址 澳门巴黎人客户端 巴黎人手机平台 澳门银河官方赌场 澳门巴黎人官方赌场 澳门银河官方下载 澳门金沙官方网址 金沙手机平台 银河现金网 巴黎人手机网站 永利官方下载 银河官方赌场 澳门永利手机网站 澳门巴黎人官方网站 澳门银河官方网站 澳门银河官方网址 澳门巴黎人官方注册 澳门威尼斯人官网 永利现金网 澳门金沙手机网站 银河客户端 澳门银河手机网址 澳门葡京客户端 巴黎人现金网 澳门巴黎人现金网 银河手机网站 澳门巴黎人老虎机 金沙手机网址 澳门巴黎人官方下载 澳门葡京轮盘 澳门金沙老虎机

Welcome to Guangzhou Wanchang Sound Co.,Ltd.

UNDERSTANDING LOUDSPEAKER DATA-002

2017-01-14 09:48:00

FS

This parameter is the free-air resonant frequency of a speaker. Simply stated, it is the point at which the weight of the moving parts of the speaker becomes balanced with the force of the speaker suspension when in motion. If you’ve ever seen a piece of string start humming uncontrollably in the wind, you have seen the effect of reaching a resonant frequency. It is important to know this information so that you can prevent your enclosure from ‘ringing’. With a loudspeaker, the mass of the moving parts, and the stiffness of the suspension (surround and spider) are the key elements that affect the resonant frequency. As a general rule of thumb, a lower Fs indicates a woofer that would be better for low-frequency reproduction than a woofer with a higher Fs. This is not always the case though, because other parameters affect the ultimate performance as well.

RE

This is the DC resistance of the driver measured with an ohm meter and it is often referred to as the ‘DCR’. This measurement will almost always be less than the driver’s nominal impedance. Consumers sometimes get concerned the Re is less than the published impedance and fear that amplifiers will be overloaded. Due to the fact that the inductance of a speaker rises with a rise in frequency, it is unlikely that the amplifier will often see the DC resistance as its load.

LE

This is the voice coil inductance measured in millihenries (mH). The industry standard is to measure inductance at 1,000 Hz. As frequencies get higher there will be a rise in impedance above Re. This is because the voice coil is acting as an inductor. Consequently, the impedance of a speaker is not a fixed resistance, but can be represented as a curve that changes as the input frequency changes. Maximum impedance (Zmax) occurs at Fs.